Front Wheel Bearing Re-Pack

[nfpgasmask]

OK, so, I am at 30k and about to take the VX on a 2000 mile drive.

Let's talk about the front wheel bearing repack. I have heard many mixed opinions about doing this service.

Please, help me out with some pros and cons. The questions I have so far:

1) How important is it in general to do this?

2) How hard is it to do for a mechanic? I am taking my truck in to have this sevice done, so I want to know what the potential is for a mech to mess it up and make them worse. Is it a straight forward thing to do if you have the experience and the proper tools?

3) If I do go ahead and have it done, what is the BEST product to lube the bearing with?

Any other info would be helpful. Thanks everyone.

Bart

[kpaske]

1) Very important. Bearings that aren't properly lubricated will heat up to very high temperatures, potentially causing damage to your hub, rotor, and axle.

2) It's not that hard. Any qualified mechanic SHOULD be able to do this without messing anything up. Always take your VX to someone you know and trust if you're not doing the service yourself.

3) Any high-temp grease will work fine.

[WormGod]

40k on mine, never had em done. Been in 2 times for solid checkups, and both times was told there was no need. That song and dance about "they are packed, sealed bearings.... you are fine. no need to really do anything until about 80k or until you sense a problem", hahaha. Considering i put about 60 miles on my VX a month now, I am in no hurry to do it. Repacked bearings on my own well near 500 times, so I think I am quite qualified to do them on my own one day anyways. That is, if my yuppie-wannabe-deskjob-computergeek-dontwannagetmyhandsdirtyanymore-self can muster up the willpower, hahahaha.

When you get the bearings packed, post the cost. Prices tend to vary quite a bit from shop to shop. Interesting seeing where many shops stand on that.

[Tone]

Wow, 40K and you've never repacked the front bearings? Ouch, grease is way cheaper than new spindles and bearings if you wait until you hear it. I'd rather do preventative maintenance instead of more expensive repairs. Even if there is sufficient grease in there, the will need to be tightened due to wear. And it is not uncommon to find water in there is you have made in deep crossings.

The backs ARE sealed and do not need to be services as they are lubricated by the diff fluid.

[nfpgasmask]

Tone, I just rolled over 30k, and I have only had this truck since May, so...

Thanks for the info. I will get this done for sure.

Bart

Wow, 40K and you've never repacked the front bearings? Ouch, grease is way cheaper than new spindles and bearings if you wait until you hear it. I'd rather do preventative maintenance instead of more expensive repairs. Even if there is sufficient grease in there, the will need to be tightened due to wear. And it is not uncommon to find water in there is you have made in deep crossings.

The backs ARE sealed and do not need to be services as they are lubricated by the diff fluid.

[WormGod]

Wow, 40K and you've never repacked the front bearings?

Yep.... like I said, I never drive it and lack of willpower. Not even sure why I have it still. To top it all off, I "have been considering" selling it outright, but that is an internal debate. I would probably only sell it to someone on these boards if I did though.

But thats crazy talk.... I dont want to think about it.

[LANINJA]

just repacked mine 5k ago myself, @105K miles on it.. they were never repacked every and the greese looked ok.. no wear on the bearing Race.. i think they could of gone longer, it was rather ez if u have the correct tools Impacket phillips is a must...