Results 1 to 7 of 7

Thread: The Resistor Nemesis

  1. #1

    The Resistor Nemesis

    Please see new post for resistor fix.

    Hey, love the VX, but if you're one of the ones that has been bitten by the resistor bug, you want to smash your head into a bare concrete wall. It's happened now during the dead of summer and now the worse NJ cold we've had.

    1. This is an obvious design defect. No car should have this happen. I've had completely rusted heater blowers on MANY cars, taken them out, cleaned them and then got them to work without electronics problems. The fact that this resistor blows with only the slightest gum on the blower is just not right. If there are other electronics problems I don't buy that either. Excuse me I'm sure you can read my frustration but this is a serious component of any car. Imagine being in the midst of nowhere when it's cold. We've had people actually freeze in cars here on our NJ Rt 80!

    2. Maybe some workaround that guarantees the blower can work on high is a good backup....I could possibly live with that till a real fix is invented. Otherwise, you really have to consider driving around with an extra resistor...and this is smart anyway because they're not readily available.

    3. Still...the ideal solution is to FIX the design defect. Any suggestions? I'm going to figure something out but really would appreciate comments. There should be a readily available switch from some other car that can be retrofitted to the VX somehow.

    4. Is Tone's "rebuild" a fundamentally better resistor? Any success stories on that? I've written to Tone and hope he is still rebuilding resistors, however the hell he does that this is some trick.

    any comments appreciated
    Last edited by -wadestock- : 12/30/2005 at 11:34 AM Reason: See FIX - heater fan doesn't work or on high only

  2. #2

    I'm holding the piece of junk in my hand right now...

    Have looked at it many times but didn't realize it's a FLEX CIRCUIT BOARD...
    Holly crap no wonder the freekin thing fissles out so easy.
    Key to its construction and functionality also appears to be the heat sink that is intimate with the flex board. Bad process or no contact on the flex board...well then instant fusible link.

    I'm going to try and get a couple of the wiz kids here to reverse engineer this and put in REAL resistors.

  3. #3
    Member Since
    Jun 2002
    Location
    '99 Ebony Black VX, 0339
    Posts
    2,073
    Thanked: 0
    Tried to respond but the mail bounced back - send them to me and I'll see what I can do.In the meantime, bypass it and the high fan will work.

  4. #4

    Further details

    There are 2 different resistors I have. One has a piece of plastic in front of the solder connections that prevents one from seeing the connections. The other one I have shows that on the one side there are actually 3 different solder connections to the flex board. 2 of them have broken off...possibly due to the current/heat generated by a sticky motor. Also, the connection BETWEEN the 2 I'm looking at also has cracked.

    Now having soldered these back, the fan still doesn't come on. And I just took the fan out and checked that it's fine. I've cleaned it and it's free wheeling.

    So....I guess soldering these connections back doesn't work. Perhaps the break is in the flex itself.

  5. #5
    Member Since
    Jan 2005
    Location
    Former owner of 01 Ironman #0723, 01 Dragon #0590
    Posts
    952
    Thanked: 0
    Is there a significant difference between the 99's and the auto control units on the 00/01's?

    I assume that there is, because it appears that the fan controls are integral to the auto control unit on the 00/01s.
    That being the case, it's probably still the same blower motor between the two models.
    The 00/01s have a power transistor paralleled with the max-high relay, everything else is in the control unit.

    Good thing too- it has warmed up to 20 degrees today.
    Sunday it was -38.

  6. #6

    Further details

    It can't be the "rebuild" of the resistor.

    If you hold the resistor in this manner....


    X...X....X
    X.........X

    The Xs being the pinouts.....then the center and top left are actually soldered together on the flex cable going into the flex resistor part. Oddly enough, the first failure mode appears to have these two connections break away from the flex cable.

    Then given enough time....failure mode NUMBER 2 is to have these two connections (essentially hanging in the breez soldered together) work their way apart and now you don't have your fan working on HIGH anymore.

    Having very obviously soldered this together....this means the fan should have come on....

    So would someone PLEASE tell me what other fuse or fusible link is in the circuit?

    Also...this means an obvious "quick fix" (provided you also don't have the "other fuse problem" I have now....is to simply jump those two connections so that your fan works on HIGH.

  7. #7

    Please...where is the OTHER resistor in the fan circuit?

    My VX is dead in the water until I find out where the other fusible link or resistor is....
    It's a 1999 and there is no fuse in the driver side box...is there something under the hood?
    What is that thing that looks like a stick that's right next to the "resistor"?????
    Last edited by -wadestock- : 12/08/2005 at 12:56 PM

Similar Threads

  1. IAT Sensor - Resistor Mod
    By SilverBullet75 in forum VX Modifications...
    Replies: 7
    Last Post: 06/13/2013, 08:56 PM
  2. A/C Blower Fan Resistor
    By Sean Rogers in forum VX Talk...
    Replies: 4
    Last Post: 12/08/2008, 06:16 AM
  3. heater resistor
    By froggg in forum VX Troubleshooting...
    Replies: 3
    Last Post: 02/22/2008, 12:06 PM
  4. Heater Resistor blown again in two months???
    By mrlegoman in forum VX Troubleshooting...
    Replies: 4
    Last Post: 02/26/2005, 02:19 AM
  5. VehiCROSS arch-nemesis?
    By WormGod in forum VX Talk...
    Replies: 39
    Last Post: 05/29/2004, 04:26 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
$lv_vb_eventforums_eventdetails