Lift Question

[TEN36VX]

Thanks for the info BritVX. What size tires are you running and how much lift did you go for?

Spazz, We discussed that stuff before. Wondering what your take on the necessity for the track extensions would be, given the geometry issue.

[Moncha]

Jay Dunford has a high lift and went with adjustable links.. See if he'll chime in here, or PM him and see what he has to say.

[BritVX]

At present I have approx' 3" lift but I'm half way through installing the plates to drop the front diff then I'll be installing the coil spacers and cranking the Torion bars again. Altogether I think it should be 4" - 4 1/2" higher. I'm running on 285/75 R16 All Terrains on 16"X10" alloys, I needed to do a slight bit of cladding trimming but nothing much. I've also done my own camber adjustment, not too difficult just very fiddling as you have to get your hands into a very small area.

SPAZZ
If the Calmini springs sag why not get the OME912s?
Also can you give me the reasoning behind extending the Trac Bars and if it's something I need to do could you give me a new length as I'll have to get them made here in the UK.


Col

[SPAZZ]

not trac bars...but the rear TRAC bar behind the axle that handles the left right angle of the axle. The rear Drag link bars that make sure your wheels do not come too far forward or backward may need to be extended a little when going with larger than 33" tires. But, they are fine for anything 33" and smaller.
OME 912's only allow for 2 1/4" to 2 1/2" lift...Calmini lifts it 3 inches and if you have the extra stiff shocks you have a really good ride. Although I'm sure you could buy the OME 912's and then the coil spacers, but when offroading such as I do the spacers fall out when I achieve max articulation( I have the sway bars disconnected). Even now I probably should wire my springs in place so when the axle articulates maxed out that the spring doesn't pop out and then jam the wiring harness that is close by. Swordy had that happen and it costs like a grand to fix.

[BritVX]

Thanks very much for the info SPAZZ I'm not sure I'll go to the extremes that I've seen in your photos but I will now look for a way of securing the cups it's a good idea.

Incidently, When adjusting my camber angle I found I had to put in 5mm of shim to correct the angle. This has reduced the thread length protruding out of the nut to 2 threads, a length I consider acceptable. When I go higher I'll obviuosly be increasing my shim thickness, if this takes the thread length below the head of the nut I'll be putting longer bolts in.
Has anyone else done this change or have you checked that it's be done by the garage if they adjusted your camber? I only mention this as the bolts are highly stressed and failure at speed would be catastrophic.

Sorry for hijacking the thread but I think the info is useful to all.

Col

[TEN36VX]

I realize this is an old threat, but I figured why start yet another on the same topic... I noticed my original question didnt really get answered.

I finally got my VX paid off so I am now ready to build my lift. I notice that the DOR and Independent kits dont have the Track Bar extension that the Calmini kit has.

How necessary is that piece?
If it's so important why doesn't anybody else make it?
Do you know how much extension it give? [I]I might just have a longer trac bar fab'ed...[/I

[SPAZZ]

call Calmini and ask them. They will tell you that they will NOT sell you individual pieces of the lift unless you have one already and unless you lie or finagle them they wil not sell individual pieces.

It took me about 45 minutes each time I called them just to get them to sell me the parts they did and each time they told me that they would not cover any of them in the event of failure at all under any circumstances.

Also, their POS suposed "BOLT ON" trac bar extension was not bolt on at all and required cutting and grinding for it to fit. They were of no help on the phone and told me I was SOL.

Their springs sagged wihin months, they wouldn't send a new set.

I can't remember how much I paid for the track bar extension, but you can try to call and see if they will sell it to you