4L30-E Transmission Heritage

[Tone]

I've been searching for HP parts for our tranny and they just don't exist. Higher stall converters would be good IF you truely raced it all the time but ours are built fairly well and do not seem to break often. That is unfortunate since anything above 5psi boost will be over spec on what the tranny can handle - I already took one out with a 150shot. Interceptor makes a big difference in longevity and increasing power throughput as it minimizes slippage that is the biggest cause of damage to a tranny.

[Joe_Black]

There are some folk out there who are building performance TC's and even an HD off-road TC for the 4L30E. It was in enough vehicles that people mod to warrant attention by at least a few vendors, and I wouldn't be surprised if your local tranny shop didn't know a few tricks too.

I've got some updates to my VX tranny maintenance page that's 4L30E specific and will post the link here once I've got it up. Tone's comments about the use of the Interceptor and the 4L30E's resilience are good info. The Interceptor does much of what a custom TC would do for less money and an easier install. What kills an auto tranny isn't HP but excessive torque, as it's hydraulically operated.

If you want a table-top tinkering project that would put you at the top of the VX envy list, get a late-model Trooper 5-speed and set it up for paddle-shift. You'd scare people with that rig!

Here's some basic 4L30E info...

4L30E

Used from 1990-up.

There are MANY versions and are used in the Cadillac Catera as well many Foreign vehicles and Postal trucks.

This is a computer controlled overdrive transmission.

Rear cooler line is the cooler return line.

Band adjustments:
Intermediate = not used
Reverse = 5 turns

Gear Ratios:
2.40:1 1st gear
1.479:1 2nd gear
1.00:1 3rd gear
0.723:1 4th gear
2.00:1 reverse

Optional Gear Ratios:
2.86:1 1st gear
1.62:1 2nd gear
1.00:1 3rd gear
0.723:1 4th gear
2.00:1 reverse

[Jonnie]

If you want a table-top tinkering project that would put you at the top of the VX envy list, get a late-model Trooper 5-speed and set it up for paddle-shift. You'd scare people with that rig!

ME ME ME!

[psychos2]

try here: http://www.levelten.com/store/index.htm they list upgrades for trooper and rodeo. shawn

[majork]

Granted the transmission was used in many vehicle types....but was it basically the same transmission in all cases, or were improvements made as it was tried in different applications

That history must exist somewhere

I did find a GM manual for the THM 4L30E dated 2003.....but it doesnt show a mod history as such....

[Joe_Black]

The only things changed beside the obvious for fitment (ratios, bell-housings and tailcones) were the actuation solenoids (what gives it the "E" designation) and control interface with the various ECU controllers and sensors. But basically a 4L30E is a 4L30E is a 4L30E. So if you've got a core laying about and want to do a rebuild, the innards will work.

[Tone]

The 2002+ 4L30E IS different from wiring and solenoid standpoint - not sure what they changed it... MAYBE the innerds are the same but the case is a bit different than the '01 tranny on the stand in my garage.

[xXxRed_Ninty_9xXx]

WAY OT BUT ITS WORTH POSTING SINCE IT WAS STATED

If you want a table-top tinkering project that would put you at the top of the VX envy list, get a late-model Trooper 5-speed and set it up for paddle-shift. You'd scare people with that rig!

Hey for those that are willing to spend over $2k here is a possible solution for any tranny swap or mods. If you beef up the 4L30E and use one of Master Shifts kits, IMHO, it would solve any questions as far as "Will TOD work?" or "What modifications do I need to do?" For the money I personally think it is worth it...in any case its worth checking out. Here is the link.

http://www.mastershift.com/