Administrator
My guess would be the actual E-Brake switch. I haven't been into the console for a while but, it should be close to the brake handle.. Use a good elertical parts cleaner and get the gunk out. the cold binds it up till it warms enough to let the spring work.
Scott / moncha.com
Super VXer
Cyrk - I been having a problem with mine as well - if I lift the e-brake handle slightly (not to the first click) - it goes off. Sometimes will stay off if I let go, most times will not. I haven't had a chance to tear the console apart, but looking atthe diagram, it looks like it may be on mount that is adjustable so maybe just needs adjustment. I'l llet you know when I get a chance to get in there.
"If you're not living on the edge --- you're taking up too much space!!"
Super VXer
Finally got the chance to open up the console and look at the problem - it was a 10 cent repair - only, I made 10 cents by fixing it! Somehow, some way, an errant dime had found its way under my console and under the e-brake switch shorting it to the chassis - which turned on the brake light. How in the hell that happened, I'll never know! With the brake handle all the way down, it pressed the switch (which activates the light) down onto the dime and created a ground which turned on the light. Go figure!
Super VXer
Well Mine turned out to be my brake pads they had eaten into my front rotors and I was not aware till it was too late... I had gotten some race pads from Hong Kong from N1 wayyy back when and they had no indicator wear on them so they wore down right into my nice expensive Powerslot rotors. I ordered some OEM pads and a set of new front Powerslot rotors and after they were installed my Ebrake light is off... weird, was not aware that they were connected to the pads/rotors.
Super VXer
the light comes on when your fluid gets low.so low fluid will also cause the light to go on. shawn
1COOLVX
Super VXer
NOT GOOD! It seems like it was not that long ago that you got those pads/rotors - are they susceptible to premature wear? I have been considering these rotors - what is your impression - would you recommend them?Originally Posted by Cyrk
Super VXer
I've ran Powerslots on two other cars.
My wife's Jetta, with EBC (Greenstuff) pads wore very well for 10,000 city miles.
My old S14, with Z32 brakes (no ABS). Running Axxis Ultimate pads, I experienced no premature wear either.
I'd say the problem is more a fault of pad selection, rather than rotors. Powerslots are nice, but expensive. There are other options for slotted rotors if that's what you like. I'm now on a pretty strict budget, so I'm going to be doing some shopping around.
If your pads were that worn, the fluid resevoir in the MC was going low every time you stepped on the brake (trying to move the cylinders a greater distance requires more fluid to be displaced). This would cause the float in your resevoir to drop down to the point where it triggered the e-brake light as a warning that you were low.
If you top off the fluid at the time of the brake pad/rotor change, it'll only get lower as your pads wear (unless you have a leak). The e-brake light is a nice warning if you don't have wear sensors to alert you.
Super VXer
Brake upgrade has been GREAT! The problem I had was getting a racing spec pad form overseas that had no indicator wear on it so when they wore down that was it... bammm right into my rotors.. I guess I should have brought it in sooner, but it did not feel that bad. The Powerslots are great and now running them with the OEM pads it feels great also make sure you add some stainless steel brake lines, that has been a great mods with the other brake upgrades. PowerSlot rotors are certainly recommend by me.
Last edited by Cyrk : 03/08/2005 at 06:14 AM
Posting Permissions
Reply With Quote
