Results 1 to 8 of 8

Thread: Air/fuel gauge

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Member Since
    Jun 2003
    Location
    02 isuzu rodeo (current red)
    Posts
    17
    Thanked: 0

    Question Air/fuel gauge

    just got an air/fuel gauge for my 02 rodeo but it saids GREEN wire from gauge to oxygen sensor or vehicle wiring harness.I looked under the car and the O2 has like 4 wires coming out of the senor so with wire do i hook it up to or find with is the wire color from the harness???????????????????????????????????

  2. #2
    Member Since
    Jun 2002
    Location
    '99 SC Ebony #1961
    Posts
    1,559
    Thanked: 0
    You need to get a single wire O2 sensor and make a new bung on your exhaust to run the air fuel, so I was told be my mechanic as that is the last gauge that I need hooked up.

  3. #3
    Member Since
    Jun 2002
    Location
    '99 Ebony Black VX, 0339
    Posts
    2,073
    Thanked: 0
    Not - refer to workshop manual cd for correct wire to tap into. Several members already have guages using stock sensors - maybe they will chime in with wire color.

  4. #4
    Member Since
    Jun 2002
    Location
    '99 SC Ebony #1961
    Posts
    1,559
    Thanked: 0
    Ok someone who has the Air/Fuel working off the stock O2 please let us know!

    Thanks!
    Dave

  5. #5
    Member Since
    Jun 2002
    Location
    2001 Proton VX 0790
    Posts
    801
    Thanked: 0
    Heres what the 4 wires are:

    2 are for the preheater.

    1 is ground.

    1 is signal, and will give a reading of about .95V.

    I have no idea what the colors are, but with a DVM it should be easy to figure out.

    That being said, I see no reason to have an O2 meter unless you are going to tune with it, and then I'd want a wideband O2 sensor.

    John C.

  6. #6
    Member Since
    Jun 2003
    Location
    02 isuzu rodeo (current red)
    Posts
    17
    Thanked: 0
    anyone know whats the wire color of the output of the O2 from the computer,and one have a workshop manual or book????And whats a DVM?

  7. #7
    Member Since
    Dec 2003
    Location
    99 white Ironman 0922
    Posts
    125
    Thanked: 0
    black is heater ground, red/white is heater power. Positive signal is green and negative signal (not ground!!!) is blue. PCM uses differential op amp to measure the voltage.

    Better choice would be to add a new single wire O2 sensor upstream of the cat and leave factory O2 wiring alone.

  8. #8
    Member Since
    Jan 2005
    Location
    '99 Blk 0089
    Posts
    207
    Thanked: 0
    Just got the Cyberdine gauge and it only has 3 wires: 2 for power and a third for signal. Should I just connect the gauge signal wire to the Green (+ power signal) wire? what about the blue (- power signal)?

    Did search but this in the only helpful post - Thanks!

Similar Threads

  1. Fuel Gauge isn't steady
    By Amnesia in forum VX Troubleshooting...
    Replies: 33
    Last Post: 04/26/2014, 12:56 PM
  2. Help: How to Replace fuel lines going to the fuel rails.
    By taylorRichie in forum VX Troubleshooting...
    Replies: 6
    Last Post: 08/10/2012, 11:10 AM
  3. wiring Air/Fuel Gauge question
    By VXtreme in forum VX Talk...
    Replies: 1
    Last Post: 03/10/2005, 09:04 AM
  4. Fuel Injectors and Fuel Pump
    By MachineVX in forum VX Talk...
    Replies: 1
    Last Post: 08/31/2004, 11:47 AM
  5. Fuel gauge
    By JAG! in forum VX Troubleshooting...
    Replies: 6
    Last Post: 03/02/2003, 09:39 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
$lv_vb_eventforums_eventdetails