Need Help... CV/axle question

[LittleBeast]

I swapped out my green cups and CV shafts with a lower mileage stock VX's OEM stuff and I had clicking while turning and it was starting to bind at speed as well and was causing the TOD to malfunction at 3.5-4" of lift (with diff drop brackets), but when I went back down to 2.5" of lift (with diff drop brackets) I had no more clicking while turning.

[89Vette]

I'm getting ready to redo both halfshafts. (Both outer CV boots have been ripped for a couple of years (10k miles). So, I'm trying to gather/locate everything I need.

I have two Empi halfshafts and spent some time looking for:

• F rotors/pads (R rotors/pads too) considering slotted
• F inner/outer bearings
• wheel bearing seal and (rear) knuckle seal.

I'm also wondering about whether the inner cup bands will need to be replaced. If so, what to use? (They don't come with the halfshafts, right?)

Anything else I'm not thinking of?

At this point in time, I'm planning on having Inland Truck do the work. They estimated $225/side after seeing right-ups provided from this great website! (Considering a move in residence and need for pituitary surgery asap,,,I'm thinking I should get this done for winter...and just in case.)

Thanks to everyone,
89V


If it matters, my mileage is 87k.

[tom4bren]

Vette,

The wear points are the inner & outer races & the bearings themselves. The cage shouldn't wear but if the joint has been running dry for a significant time then it could have wear as well. I'm not familiar with the Empi shafts so I don't know what OEM parts they are compatable with.

Good luck with your surgery & relocation. A buddy of mine at work had similar surgery a few years ago with a quick recovery & no adverse effects. IIRC he had a small tumor on his pituitary gland.

[89Vette]

Vette,

The wear points are the inner & outer races & the bearings themselves. The cage shouldn't wear but if the joint has been running dry for a significant time then it could have wear as well. I'm not familiar with the Empi shafts so I don't know what OEM parts they are compatable with.

Good luck with your surgery & relocation. A buddy of mine at work had similar surgery a few years ago with a quick recovery & no adverse effects. IIRC he had a small tumor on his pituitary gland.

Recently, in another thread, I mentioned my confusion about the EMPI shafts having different size balls (bearings) than stock. This didn't seem possible/likely since they need to correctly mate to the "receiving end" of the joint. If not, I can't see how they wouldn't pop and wear inappropriately.

I'm expecting the Empi's to bolt right in...and be compatible with OEM parts.

I hadn't thought of anything like a race but I don't think any bearings are bad. Don't hear any of that type of noise anyway. I just want to have them on hand for the mechanic. And, for jobs like this, you always wonder if a new bearing race (along with any other reasonably-priced parts aren't better replaced during the operation.

Speaking of operation,,,my tumer is getting pretty big. I think doctors let it go too long as it's over an 1" in diameter. Not looking forward to it...but know it's gotta be done. I appreciate the vote of confidence though!

[tom4bren]

BTW, if the kit did not come with the bands for the boots, the shop should either have some on hand or be able to get them. As an alternative, I used heavy duty zip ties on mine for 2 years with no problem.

Either pick up or tell the shop that you want synthetic grease when they assemble the CV. Marine grease would be even mo betta.

This might help you locate some of the parts you're looking for:

[VXorado]

BTW, if the kit did not come with the bands for the boots, the shop should either have some on hand or be able to get them. As an alternative, I used heavy duty zip ties on mine for 2 years with no problem.

Nice, I use zip ties too. I use two smaller (width) zip ties per one metal band.

Haven't had any issues and they're much easier to install.

[tom4bren]

Nice, I use zip ties too. I use two smaller (width) zip ties per one metal band.

Haven't had any issues and they're much easier to install.

Thanks for refreshing my rememory. The HD zipties were too wide & didn't stay in place so I ended up using ordinary grade zipties instead & they worked much mo betta.