Results 1 to 15 of 63

Thread: Need Help... CV/axle question

Threaded View

SilverBullet75 Need Help... CV/axle question 01/28/2012, 07:52 AM
89Vette Edit: Retracted all... 01/28/2012, 09:11 AM
SilverBullet75 oh, i forgot to mention that... 01/28/2012, 09:22 AM
VXorado Its an easy install, the half... 01/28/2012, 01:37 PM
SilverBullet75 Thank you!!!!!!!!! That's... 01/28/2012, 01:46 PM
Vendetta I wish I spoke whatever... 01/28/2012, 01:57 PM
SilverBullet75 Believe me... I had to have a... 01/28/2012, 02:08 PM
VXorado Wait until you grenade a CV,... 01/28/2012, 02:13 PM
Vendetta I'm starting to feel the... 01/28/2012, 02:25 PM
FenderBender I just put a PS shaft... 01/28/2012, 03:01 PM
Ldub This is not a :( moment, this... 01/28/2012, 04:25 PM
Triathlete My Empi shafts have held up... 01/28/2012, 04:37 PM
SilverBullet75 Ok, I just got back from... 01/28/2012, 04:45 PM
SilverBullet75 What type of grease goes on... 01/28/2012, 05:42 PM
89Vette Even though I've read a... 02/03/2012, 08:19 PM
rowhard I often do that just to see... 06/25/2012, 05:00 PM
89Vette Copy that Rowhard! ... 06/30/2012, 08:27 AM
Jonnie http://www.vehicross.info/foru... 02/04/2012, 09:00 PM
Triathlete Or... They weld the scarring... 04/27/2012, 10:23 PM
Triathlete The grease will hold them in. 06/30/2012, 08:54 AM
89Vette Thanks, that's what I hoped. ... 06/30/2012, 10:11 AM
Triathlete Nah, the grease is thick and... 06/30/2012, 12:14 PM
SilverBullet75 They also kinda "click" into... 06/30/2012, 03:43 PM
LittleBeast I swapped out my green cups... 07/02/2012, 11:10 AM
89Vette I'm getting ready to redo... 11/27/2012, 10:55 PM
tom4bren Vette, The wear points are... 11/28/2012, 05:25 AM
89Vette Recently, in another thread,... 11/28/2012, 06:24 AM
Leon R The new (Chinese) axles are... 11/29/2012, 08:37 AM
Previous Post Previous Post   Next Post Next Post
  1. #1
    Member Since
    Feb 2004
    Location
    '01 Ebony #0830
    Posts
    1,097
    Thanked: 0

    Exclamation Need Help... CV/axle question

    Hi,
    Need to know if the front CV axles (cv to cv) are identical left and right.
    Napa has them in stock for $87 each, but they are listed as Right side on the part description.
    I measured both shafts and they are both 19.75" long.
    I was going to just put new boots on, but then found that the cvs are pitted badly and overheated/melted/rubbed/pooled (I hope that's a good enough description).
    I know about the Empi's being ok, but has anyone had experience with Napa shafts?
    These are new, not rebuilt.
    part number: 94-6029
    I did a search, but couldn't find this specific info.
    Also, I ordered cv boots from Napa and they are Empi brand, relabled for Napa.
    So, hoping the cv shafts are Empi too...

    Also, if the shafts are not correct, can the CV's be swapped to the original shafts?
    Thank you for any help!
    ---JIM---
    Last edited by SilverBullet75 : 01/28/2012 at 08:28 AM Reason: clarification...
    SilverBullet75
    Formerly: '01 Ebony VXSTLTH
    Now: '08 Saab 9-7x Aero 6.0L

Similar Threads

  1. Axle seal?
    By LittleBeast in forum VX Troubleshooting...
    Replies: 13
    Last Post: 09/17/2017, 11:57 AM
  2. Axle seal?
    By VehiTONY in forum VX Troubleshooting...
    Replies: 13
    Last Post: 05/20/2014, 08:24 AM
  3. EMPI CV axle fitment question/issue
    By spaceghost in forum VX Troubleshooting...
    Replies: 14
    Last Post: 10/25/2013, 10:14 PM
  4. Why is this on the axle???
    By VXorado in forum VX Troubleshooting...
    Replies: 7
    Last Post: 11/11/2011, 11:51 AM
  5. Rear Axle Question
    By Buffy in forum VX Talk...
    Replies: 4
    Last Post: 10/18/2010, 07:35 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
$lv_vb_eventforums_eventdetails