Results 1 to 15 of 40

Thread: Head gaskets...

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Member Since
    Mar 2006
    Location
    2001 FOXFIRE 0579
    Posts
    887
    Thanked: 0

    It's ALIVE........but....

    I did something to the tranny. It is Downshifting really hard 3rd to 2nd and then 2nd to 1st.
    I know what I did, just don't know what I may have done.
    When taking apart the exhaust, the manual said to remove the third crossmember. So I start undoing bolts on the crossmember wondering what will hold the transmission up if I take the off?
    Well I had a jack under it, and undid the bolts , then realized the jack wast tight, and it sank a good inch before I was able to tighten it. So I put bolts back in a bit, because I now had some clearance I needed.
    So last night raised the tranny back up and bolted everything up tight (I am missing one of the bolts under the skid plate) and I finished the last of the reassembly, hooked up the battery,
    And the truck fired right up, (I got video!)
    So tonight I took it for a short drive. It is still smoking, and downshifts hard

    Anythoghts on what I put in a bind when I jacked the tranny back up, or what I may have broke? It upshifts fine, and wasn't having any abnormal shifting before this project. It has to be IMO from me moving the tranny?

  2. #2
    Member Since
    Jun 2004
    Location
    99 Astral Silver VX #1872 + 99 Ironman WIP
    Posts
    10,613
    Thanked: 1

    Wrench

    Quote Originally Posted by IndianaVX View Post
    I did something to the tranny. It is Downshifting really hard 3rd to 2nd and then 2nd to 1st.
    I know what I did, just don't know what I may have done.
    When taking apart the exhaust, the manual said to remove the third crossmember. So I start undoing bolts on the crossmember wondering what will hold the transmission up if I take the off?
    Well I had a jack under it, and undid the bolts , then realized the jack wast tight, and it sank a good inch before I was able to tighten it. So I put bolts back in a bit, because I now had some clearance I needed.
    So last night raised the tranny back up and bolted everything up tight (I am missing one of the bolts under the skid plate) and I finished the last of the reassembly, hooked up the battery,
    And the truck fired right up, (I got video!)
    So tonight I took it for a short drive. It is still smoking, and downshifts hard

    Anythoghts on what I put in a bind when I jacked the tranny back up, or what I may have broke? It upshifts fine, and wasn't having any abnormal shifting before this project. It has to be IMO from me moving the tranny?
    Check that part of the wiring harness that's factory connected to the cross memeber...

  3. #3
    Member Since
    Apr 2004
    Location
    2000, Ebony, VX, 0370
    Posts
    2,503
    Thanked: 12
    I know this is simplistic, and I really have no idea what I'm talking about, but could it be that the fluid in the transmission shifted while it was in a lowered position and just needs some time to level back out so it will shift normally?

    I figure; check the easy (cheap) stuff first.
    "The major difference between a thing that might go wrong and a thing that cannot possibly go wrong is that when a thing that cannot possibly go wrong goes wrong, it usually turns out to be impossible to get at or repair."
    -Douglas Adams, Mostly Harmless

  4. #4
    Member Since
    Dec 2008
    Location
    01, LineX tan/black, 1055
    Posts
    3,380
    Thanked: 0
    Quote Originally Posted by MSHardeman View Post
    I know this is simplistic, and I really have no idea what I'm talking about, but could it be that the fluid in the transmission shifted while it was in a lowered position and just needs some time to level back out so it will shift normally?

    I figure; check the easy (cheap) stuff first.
    I would say no, based on the fact that I have had my VX tipped front side up, back side up, sideways, and never had a shifting problem. His was only a few inches off, so I doubt it would make much difference? Plus, tranny fluid isn't that thick, it would move fairly quick, especially at 150 degrees or whatever it runs at...

    I predict future happiness for Americans if they can prevent the government from wasting the labors of the people under the pretense of taking care of them.
    Thomas Jefferson

  5. #5
    Member Since
    May 2006
    Location
    SOLD!
    Posts
    7,257
    Thanked: 2
    I'd say check the fluid level, check the connectors, and also check the mode selector. Maybe when it sank it pulled something down to much and messed up the mode switch somehow??? That's all attached to your shift selector and maybe the mode switch cracked or broke or something?

    When was the last time you checked/changed the fluid and filter? Might be a good time to do that. Who knows, maybe the tranny issue is just a coincidence.

    Bart

  6. #6
    Member Since
    Mar 2006
    Location
    2001 FOXFIRE 0579
    Posts
    887
    Thanked: 0
    something to consider,

    the "D" on my dashboard has been out for months. i cleaned the switch underneath the shifter, by the tranny, when it first happened. it was dirty, now its not, and the "D" is still out on the dash. so i figured the bulb must be out. and there was not any odd shifting problems in all that time.

    my power mode light has been out for around a month, before this all happened. the winter mode still works fine, and the winter light on the dash works.
    the truck feels like it is in power mode, even if the dash light doesnt tell me so. so again, i figured another bulb is burnt.

    fluid in tranny was checked this fall, and was right where it should be.
    a change and filter has been on my to do list. but i got alot of other list also.......

    i just feel like something happened when i lowered the tranny down that bit.

    thanks for the input thus far. i cant stand being this close to driving again. the things i was worried about, (timing, timing belt, etc) went so smoothly, and the thing that wasnt really even on the radar, is giving me fits.
    thanks again!

  7. #7
    Member Since
    Mar 2006
    Location
    2001 FOXFIRE 0579
    Posts
    887
    Thanked: 0

    And another thought.....

    I'm sure that after having coolant going thru the exhaust, I imagine my pre cat O2 sensors are probably shot. Could they be sending any bad, or no signal to the ECU and making the poor shifts?
    I looked at all the electronic plugs, and couldn't find any problems.
    Back to the shop manual.........

Similar Threads

  1. Head Gaskets
    By 303Foxfire in forum 10 Year Anniversaries...
    Replies: 1
    Last Post: 04/11/2016, 07:45 PM
  2. fricking rubber gaskets
    By p_justin13 in forum VX Troubleshooting...
    Replies: 9
    Last Post: 02/25/2010, 07:03 AM
  3. New Head Gaskets Major Problems
    By BHP in forum VX Troubleshooting...
    Replies: 9
    Last Post: 01/27/2008, 08:45 AM
  4. U.K. Owner needs help with head gaskets
    By David Wiltshire in forum Japanese Domestic Model (JDM) VXs
    Replies: 6
    Last Post: 04/19/2007, 11:32 AM
  5. Intake gaskets and SC VX
    By MachineVX in forum VX Troubleshooting...
    Replies: 11
    Last Post: 05/06/2005, 12:07 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
$lv_vb_eventforums_eventdetails