Page 1 of 3 1 2 3 LastLast
Results 1 to 15 of 40

Thread: Intermittant High Idle (again)

  1. #1
    Member Since
    Jun 2009
    Location
    2000, Kaiser, #0016
    Posts
    645
    Thanked: 0

    Intermittant High Idle (again)

    As posted in a different thread, I have an intermittant high idle prob. Thought I had fixed it, but its back. So far I have cleaned the Mass Air Flow (MAF) sensor and yes I used sensor safe cleaner, replaced the Idle Air Control valve (IAC), and Throttle Position Sensor (TPS), cleaned the throttlebody, checked for intake manifold gasket leaks via spraying around the manifold with carb cleaner.

    I cannot rule out other vacuum leaks as I dont really know where to look or a easy method of locating them, but nothing really stands out as far as cracked or missing hoses.

    The PCM never throws codes, CEL light never turns on despite idle that somtimes reaches 2600RPM! Somtimes it idles ok tho, but usually around 1000-1200. PCM appears working because my OBDII reader sends live real-time data to my Droid phone just fine. (can the PCM just partially fail?)

    Here is what I have left IMHO:

    Some here have suggested fuel pressure regulator. I don't know how to test this. Other forums have reported possible fuel pump itself.

    Some vacuum leak SOMEWHERE, again, how to test?

    One forum found a fix on a 3.5L trooper in that the power steering pump pressure sensor may be failing. On that forum the diagnoses was apparently correct. Apparently the logic goes that when that sensor gives a low reading, the PCM bumps up the idle to increase pressure in the lines. I find this interesting as the last time my oil was changed, the ppl there showed me some leakage they identified as power steering fluid. It was apparently a slow leak as it never drips on the driveway, but it was leaking around or onto the "intercooler" where it enters the radiator (lower left side of the radiator as you face the front of the VX). They showed me the evidence of the leak, it was definitely red fluid. They were not concerned as the leak was apparently small.

    So... any pro-tips? I really, really do not want to go to an average joe mechanic only to have him replace all the stuff I already replaced (which to me are the obvious and easy things). Only to have to have it back the next week for the same problem. At that rate this could take months and hundreds of dollars of labor costs before its fixed.

    Any thoughts appreciated.

    Oh and for you ppl with Scangauge or other realtime OBD interfaces, where can I find proper baseline numbers for what I *should* be reading from data such as MAF and intake pressure?
    Last edited by Grif : 05/23/2010 at 09:37 PM

  2. #2
    Member Since
    Jun 2004
    Location
    99 Astral Silver VX #1872 + 99 Ironman WIP
    Posts
    10,613
    Thanked: 1

    Wrench

    FWIW, though probably not a lot of help...

    The fluid leak by the "intercooler" would more likely be trans fluid, as I'm not aware of the power steering system being run through the radiator...

  3. #3
    Member Since
    Jun 2009
    Location
    2000, Kaiser, #0016
    Posts
    645
    Thanked: 0
    Yeah Ldub, I was curious about that too. But the fluid was dripping onto the intercooler, not from it apparently. They seemed pretty convinced it was steering fluid.

  4. #4
    Member Since
    Jun 2009
    Location
    2000, Kaiser, #0016
    Posts
    645
    Thanked: 0
    Ok, put it in the shop. They were unable to find any external vac leaks. They could not rule out internal vac leaks (WTF are internal vac leaks??)

    The shop found the info about the power steering pressure sensor possibly causing this, so they started to check that out, but in the process found a broken wire from an oil pressure sensor (tho the invoice indicated it was an oil pressure SWITCH) and once that wire was corrected the idel went down nearly to normal.

    They were as suprised as I was.

    So I got the VX back from the shop, and to me the idle is still a bit high. But at least not 2000-2600 RPM.

    I had never heard of this potential cause before so I post it here. I think it will take more testing before I'm convinced because the high idle condition was intermittant anyways. I post the info from the shop here simply because it was news to me.

  5. #5
    Member Since
    Jun 2009
    Location
    2000, Kaiser, #0016
    Posts
    645
    Thanked: 0
    No comments? No replies? Despite the fact the I've proposed a new fix for scroggy idle probs?

    Despite the fact that I requested baseline OBD measurements from you scanguage owners?


    My posts have been buried. I'm feeling kinda alone here.

  6. #6
    Member Since
    May 2003
    Location
    '99 Astral #1613
    Posts
    1,317
    Thanked: 0
    Mine has been doing something similar, idling around 1200 rpm, shooting up to over 2000 rpm (sometimes well over) when in neutral or park. Surging while driving, seems to be mostly during deceleration coming to a light and such. Was sitting in line at a drive-thru and it was revving up pretty good and got way hot. One time it got real hot and also had really rough transmission shifts, but only once did that happen. Inspection showed some serious oil consumption and water was low.

    Had erratic idle a while back but not the surging, etc. Replaced the IAC back then, problem pretty much went away until a week or so ago when all of this started occurring.

    So anyway, a little over a week ago it started surging pretty bad then getting too hot. Got a CEL when it overheated, oil & water low, changed oil, added water, new air filter while I was at it. Checked PCV, sprayed IAC and throttle butterfly valve with carb cleaner. Have not done EGR though. Has not overheated or thrown another CEL since but still was surging. Problem is intermittent, may act weird right at start-up, drive great for 30 minutes of so, then start misbehaving. Some times worse, some times not at all. No apparent leaks other than a very slow power steering fluid leak I've known about for some time. Was advised to just keep an eye on it, shop was in no hurry to replace the pump and didn't seem to think it was a big deal.

    VX was finally in the shop today and the code they got indicated a faulty throttle position sensor. Would be nice if that's it because it wasn't obscenely expensive ($40 part, though that is a lot for no more than it is). Since that was replaced this afternoon it is still idling a bit high, just over 1000 rpm, but if I shift it into drive while sitting still it settles to normal idle speed. Short little drives tonight yielded no surging though, will see how it goes from here.

    I forgot to tell them not to use the windows, and it seems like mechanics always do. So the window glass came off the lift mechanism, dropping the glass free into the door. Since they made no attempt to make it right after doing it and I was sort of mad about that and would pretty much just rather they didn't anyway, I had to pull the door apart tonight and get it back in place. Got that down to a science now, done it plenty. It's a wonder the glass has not broken yet. The rubber in the forward channel is totally shot and needs replacement. I like using my windows and my main gripe with the VX is I've had mine since 2003 and the windows have never worked right. Really crappy design.
    Last edited by Heraclid : 05/28/2010 at 09:55 PM

  7. #7
    Member Since
    May 2009
    Location
    1999 Ebony Black/Red
    Posts
    145
    Thanked: 0
    i had nissan 300zx z32 few years back. those cars are "famous" for their cheap wiring -> easily/quickly corroding, causing very rough idle/poor perfomance. since you said there is, possibly, electrical problems, I would check the wires and connections by the wre that goes to oil pressure regulator and would shaken the other ones, particuularly the wires which power the injectors

  8. #8
    Member Since
    Feb 2006
    Location
    2001,Kaiser Silver, VX, 0563
    Posts
    4,767
    Thanked: 0
    i could give you some scangauge measurements from idle, but would need more specifics. do you want a cold start? or a warm start? AC on or off?

    I also have aftermarket intake filter and exhaust, so that may make a difference, let me know what youre looking for and ill do what i can


    "Engineers believe if it ain't broke, it doesn't have enough features yet"

  9. #9
    Member Since
    Jun 2009
    Location
    2000, Kaiser, #0016
    Posts
    645
    Thanked: 0
    Thx ETL,

    Mostly I would be intrstted in startup, cold start, AC off idle. Cuz thats where I start my measurements. I'm looking to get ideal baseline numbers. Your intake should not matter much since if working properly, the computer should aadjust. If you can provide more numbers such as when coolant gets above 180F or so might be helpfull.

    But whatever number you can give me under both cold start and warm running driving may help..

    Thx bro, I trust your opinion.

  10. #10
    Member Since
    Jun 2009
    Location
    2000, Kaiser, #0016
    Posts
    645
    Thanked: 0
    BTW started it up today, and it would hardly run at idle. Without my foot on the pedal, it would simply die. had the shop change plugs and fuel filter when it was there. But same prob. Drove approx 10 miles, parked for about 15 mins, started it again and it went up to 1500 RPM at idle. Revved the engine to see if it would shake back down, nope. Then drove the same 10 miles back home, on the way i stopped at several lights, it was back up to 2000RPM. Five mins later I was home and idle was perfect at 700. Let it sit for an hour or so, went out and started it up to play with some audio stuff, and it wouldnt idle below 2000 again.

    This is frickin nuts.

    Its going back to the shop on tuesday. I have nothing left to try from the advice from folx here but demand they replace the fuel pressure regulator. Either that or check every wire from every sensor. Its still not throwing any CEL codes whatsoever.

  11. #11
    Member Since
    Jun 2009
    Location
    2000, Kaiser, #0016
    Posts
    645
    Thanked: 0
    So back to the shop it went, they pulled the power steering fluid sensor off, and bam, it went back down to 1000RPM cold idle. I'll drive it a few more days and see how it goes. Luckily they didnt charge me for this re-visit.

    The shop owner stated that if it were him, he would just leave the sensor off unless I was planning on racing it or somthing. I dont know if thats a good idea or not as I tend to have a lead foot.

    Still, its not 700-750 which I gather is ideal. What do you all think? Leave the sensor off? (i cant imagine its very expensive, and could prolly replace it myself). And should I still demand 750RPM warm idle?
    Last edited by Grif : 06/02/2010 at 08:15 PM

  12. #12
    Member Since
    Aug 2008
    Location
    2001, PROTON YELLOW, VehiCROSS, 1451
    Posts
    1,955
    Thanked: 0
    Quote Originally Posted by Heraclid View Post
    Mine has been doing something similar, idling around 1200 rpm, shooting up to over 2000 rpm (sometimes well over) when in neutral or park. No apparent leaks other than a very slow power steering fluid leak I've known about for some time. Was advised to just keep an eye on it, shop was in no hurry to replace the pump and didn't seem to think it was a big deal.
    Hmmm, seems like a common malfunction in regards to the "POWER STEERING" system (faulty PS connections/pump, leaky PS reservoir, low PS fluid levels).

  13. #13
    Member Since
    Jun 2009
    Location
    2000, Kaiser, #0016
    Posts
    645
    Thanked: 0
    Quote Originally Posted by Riff Raff View Post
    Hmmm, seems like a common malfunction in regards to the "POWER STEERING" system (faulty PS connections/pump, leaky PS reservoir, low PS fluid levels).
    Correct Riff, it does seem to be a common problem. I had even mentioned it to the shop the first time I brought it in. But whats your point?

  14. #14
    Member Since
    Aug 2008
    Location
    2001, PROTON YELLOW, VehiCROSS, 1451
    Posts
    1,955
    Thanked: 0
    Quote Originally Posted by Grif View Post
    Correct Riff, it does seem to be a common problem. I had even mentioned it to the shop the first time I brought it in. But whats your point?
    My point is any other VX owner who is, has, or will experience simular high-rev symptoms may want to investigate their PS system as a possible culprit. Thanx for the feedback, as your experiences help all of us maintain our VX's in proper running condition and help solve the mystery sometimes with mechanical gremlins.

  15. #15
    Member Since
    Feb 2006
    Location
    2001,Kaiser Silver, VX, 0563
    Posts
    4,767
    Thanked: 0
    some baseline numbers

    Ambient Temperature 82ºF
    Relative Humidity 87%
    Time without running - 10Hours

    Initial startup, no AC
    Water Temp - 83
    RPM - 960-1000
    Throttle Pos - 0
    Air/Fuel Ratio - 15.2
    HP - 15.3
    Voltage - 13.8
    Intake Temp - 82
    Gallons/Hr - 0.8
    IGN - 16
    Engine Load - 6
    Closed Loop
    Manifold Pressure - 4.9

    Running time approx 90 seconds, AC full blast
    Water Temp - 112ºF
    RPM - 975-990
    Throttle Pos - 0
    Air/Fuel Ratio - 14.7
    HP - 13.9
    Voltage - 13.4-13.6
    Intake Temp - 85
    Gallons/Hr - 0.5
    IGN - 16-17
    Engine Load - 7
    Closed Loop
    Manifold Pressure - 5.4

    Running Time approx 3 minutes, A/C off
    Water Temp - 155
    RPM - 940-950
    Throttle Pos - 0
    Air/Fuel Ratio - 14.7
    HP - 10.2
    Voltage - 13.8
    Intake Temp - 105ºF
    Gallons/Hr - 0.62
    IGN - 16
    Engine Load - 5
    Closed Loop
    Manifold Pressure - 4.4

Similar Threads

  1. High Idle suddenly =/
    By Breezy in forum VX Troubleshooting...
    Replies: 21
    Last Post: 11/19/2011, 03:47 AM
  2. Another high idle problem
    By RAZ in forum VX Troubleshooting...
    Replies: 20
    Last Post: 07/13/2011, 11:59 AM
  3. High idle/ high power steering pressure?
    By Rene M in forum VX Troubleshooting...
    Replies: 1
    Last Post: 09/22/2007, 03:21 PM
  4. High idle question
    By zadam123 in forum VX Troubleshooting...
    Replies: 15
    Last Post: 01/18/2007, 05:14 PM
  5. RPM to high at idle
    By ThunderChicken in forum VX Troubleshooting...
    Replies: 6
    Last Post: 09/23/2004, 11:09 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
$lv_vb_eventforums_eventdetails