CV joint replacement

[PK]

Yep, none of the other how tos showed to remove that stupid ring inside the green cup.

The how to for CV boot replacement clearly shows that snap ring and how to remove it.
That is what I have used for each boot replacement I have done.

PK

[Marlin]

The how to for CV boot replacement clearly shows that snap ring and how to remove it.
That is what I have used for each boot replacement I have done.

PK

I searched for CV joint replacement, and found nothing about the stupid snap ring. I also looked at the tech manual, it just says something like "remove the CV axle shaft" or something along those lines.
Wow, I just looked at the CV boot how to, strikingly similar to what I came up with on my without any guidance...lol. Rework, gotta love it. I am curious to know how the CV joint came out without removing the calipers or the tie rod. I could not get near enough clearance without doing that, and mine was missing the last 2 inches of the CV shaft!! He also didn't mention removing the hub and the outer snap ring? Plus the ABS sensor is kind of a PITA since it is the most limiting component. The 1st time I did this I had to take the wire our of all the brackets and disconnect the harness. This time, I just cut them I think the big difference is that those are just boot swaps, you don't have to pull the whole CV out to do that. Mine was for replacing the entire CV joint.
Well, that write up is clearer than mine, and skips a lot of the things I did, such as removing calipers to minimize stress on the brake lines, and saves chance of tie rod end damage when breaking it loose. I will try again when I do the other side. Although, I have to replace the ball joints anyway.
Thanks Jack for the heads up.
(As I humbly walk away with my head hanging low and tail between my legs.)

[PK]

I searched for CV joint replacement, and found nothing about the stupid snap ring. I also looked at the tech manual, it just says something like "remove the CV axle shaft" or something along those lines.
Wow, I just looked at the CV boot how to, strikingly similar to what I came up with on my without any guidance...lol. Rework, gotta love it. I am curious to know how the CV joint came out without removing the calipers or the tie rod. I could not get near enough clearance without doing that, and mine was missing the last 2 inches of the CV shaft!! He also didn't mention removing the hub and the outer snap ring? Plus the ABS sensor is kind of a PITA since it is the most limiting component. The 1st time I did this I had to take the wire our of all the brackets and disconnect the harness. This time, I just cut them I think the big difference is that those are just boot swaps, you don't have to pull the whole CV out to do that. Mine was for replacing the entire CV joint.
Well, that write up is clearer than mine, and skips a lot of the things I did, such as removing calipers to minimize stress on the brake lines, and saves chance of tie rod end damage when breaking it loose. I will try again when I do the other side. Although, I have to replace the ball joints anyway.
Thanks Jack for the heads up.
(As I humbly walk away with my head hanging low and tail between my legs.)

Hey Man, don't go on a downer on me. LOL.
As you mention in your post, your write up was for replacing the whole CV joint. The other how to is just for the boots, and works great for the boots.
But you cannot replace the whole joint without including at least some of the points your write up covers.
I only mentioned the other write up because it did mention the snap ring that you found the hard way.
Keep up the good work Marlin.
You are obviously enjoying your new found skills.

PK

[LittleBeast]

I searched for CV joint replacement, and found nothing about the stupid snap ring. I also looked at the tech manual, it just says something like "remove the CV axle shaft" or something along those lines.
Wow, I just looked at the CV boot how to, strikingly similar to what I came up with on my without any guidance...lol. Rework, gotta love it. I am curious to know how the CV joint came out without removing the calipers or the tie rod. I could not get near enough clearance without doing that, and mine was missing the last 2 inches of the CV shaft!! He also didn't mention removing the hub and the outer snap ring? Plus the ABS sensor is kind of a PITA since it is the most limiting component. The 1st time I did this I had to take the wire our of all the brackets and disconnect the harness. This time, I just cut them I think the big difference is that those are just boot swaps, you don't have to pull the whole CV out to do that. Mine was for replacing the entire CV joint.
Well, that write up is clearer than mine, and skips a lot of the things I did, such as removing calipers to minimize stress on the brake lines, and saves chance of tie rod end damage when breaking it loose. I will try again when I do the other side. Although, I have to replace the ball joints anyway.
Thanks Jack for the heads up.
(As I humbly walk away with my head hanging low and tail between my legs.)

Yeah I was wondering why you took the brakes apart as well, I have done work on the CV's a million times it seems like and I never messed with the brakes or ball joints. Just taken off the 4 lower bolts on the lower control arm/ball joint seems to loosen everything enough. It is really fun getting to know the VX though, and some people are able to get the front diff out without even taken apart the center steering link, which is great because that may be the #1 most difficult thing to remove on the VX. I ruined my center link last time I was removing it only to figure out a way to get the diff dropped without totally take it out, but just getting the passenger side loose Learning your VX is half the fun in wrenching though. I betcha I might have the only VX with Home Depot bolts holding together the control arm on the steering

[Ldub]

Where's the step where you add a full tube of fresh CV grease?...

[Marlin]

Where's the step where you add a full tube of fresh CV grease?...

I was putting a new CV in, so I had already done that I was very impressed that the old grease was in great shape! I think they were the original boots as well, no tears, but they were starting to crack, so only a matter of time I suspect.
Next, check out your tip on the lower link.

[tom4bren]

Marlin,

It all depends on what you are tearing it apart for. If you're just replacing boots or stuffing new inner races & bearings into the existing outer race then the DL instructions are easies. If you need to pull the axles for changing the outer race, then you'll need to go through all that you did.

[Marlin]

[QUOTE=LittleBeast;191601] It is really fun getting to know the VX though, and some people are able to get the front diff out without even taken apart the center steering link, which is great because that may be the #1 most difficult thing to remove on the VX. QUOTE]

When I did mine, the 1st time I spent quite a while hammering at the pitman arm with the puller as tight as I cuold get it for fear of my life. turns out if you just loosen the 4 bolts that hold the steering box on, the arm will just pop out with hammering I learned that the hard way.