Page 1 of 2 1 2 LastLast
Results 1 to 15 of 22

Thread: Kilby skid plates + diff drop?

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Member Since
    Oct 2003
    Location
    1995 Isuzu Trooper LS
    Posts
    1,082
    Thanked: 3

    Kilby skid plates + diff drop?

    Has anybody installed their Kilby skids yet? I haven't noticed any chatter since the group buy.

    More specifically, has anybody with a diff drop installed Kilby skids? I was looking under the Trooper yesterday, and it sure seems like significant modification will be needed to make it work with a diff drop. It looks like the replacement crossmember will pass right through the dropped front driveshaft. This is important, since the skid plates attach to that crossmember. And the diff pumpkin looks pretty low too.
    95 Trooper with a buncha stuff nobody here cares about...

  2. #2
    Member Since
    Dec 2008
    Location
    Former owner 2001, Foxfire Red, #0663
    Posts
    7,311
    Thanked: 33
    I got mine installed, but I don't have diff drop.
    Here's pics, maybe it will help you, but I know you have a Trooper.
    Pics start at post #128
    http://www.vehicross.info/forums/sho...ght=kilby+skid
    VX KAT
    ....the adventure BEGINS ANEW! ...2015......
    Remember that life is not measured in the breaths you take, but rather in the moments that take your breath away.

  3. #3
    Member Since
    Jun 2004
    Location
    99 Astral Silver VX #1872 + 99 Ironman WIP
    Posts
    10,613
    Thanked: 1

    Talking

    Quote Originally Posted by VX KAT View Post
    I got mine installed, but I don't have diff drop.
    Here's pics, maybe it will help you, but I know you have a Trooper.
    Pics start at post #128
    http://www.vehicross.info/forums/sho...ght=kilby+skid
    Here's a short short shortier short cut, directly to post 128...

    http://www.vehicross.info/forums/sho...&postcount=128

  4. #4
    Member Since
    Feb 2007
    Location
    2000 Proton VX - 0776
    Posts
    9,258
    Thanked: 0
    See post #140 here:

    http://www.vehicross.info/forums/sho...ighlight=Kilby

    As far as the diff drop:

    I've got a set of brackets to lower the new crossmember to clear the diff but that'll only be part of your problem. Lemme know.

    If you drop the crossmember then the angle of the plate will be wrong for the mounting holes to line up. You may be able to get away with this with just some longer bolts. If not, you should be able to get the plates modified at a machine shop in your area.

    Short short shortier short cut to post #140 (see Ldubs post below):

    http://www.vehicross.info/forums/sho...&postcount=140

    KAT - when you find the post in a particular thread that you want to direct someone to - click on the post number and it opens up that post in a new window. Copy that url to the thread you're referencing from. (Just a Handee little tidbit of info for future reference).
    Last edited by tom4bren : 04/12/2010 at 08:51 AM
    [SIGPIC][/SIGPIC]

    Put a smiley after you say that Bub.

  5. #5
    Member Since
    Dec 2008
    Location
    Former owner 2001, Foxfire Red, #0663
    Posts
    7,311
    Thanked: 33
    Quote Originally Posted by tom4bren View Post
    KAT - when you find the post in a particular thread that you want to direct someone to - click on the post number and it opens up that post in a new window. Copy that url to the thread you're referencing from. (Just a Handee little tidbit of info for future reference).
    TANKS T4B....I've done that before, but musta not had enuf java juice yet dis mornin'....not firin' on all 3 brain cells yet!

  6. #6
    Member Since
    Oct 2003
    Location
    1995 Isuzu Trooper LS
    Posts
    1,082
    Thanked: 3
    Thanks guys, I lost track of that thread. The skids look very nice and should work well.

    Though you might want to invest in a set of Irwin Bolt Grip extractors for deformed bolt heads...or maybe if you can find something like an allen head carriage style bolt, those would be a lot less likely to catch on rocks and such.

    Getting back to my original point, with the diff drop I am quite sure the crossmember will have to be substantially modified. By eyeball, it looks like the crossmember and diff pinion intersect almost exactly. I am actually thinking it might be best to bridge the crossmember over the driveshaft/diff pinion instead of under it, but a test fitting will be necessary to really judge that.

    And, the diff pumpkin will almost certainly intersect the front angled plate. A clearance hole will have to be cut, and maybe a bridge built over the hole to protect the pumpkin.

    But I was hoping somebody had done all this already and could tell me exactly what is needed...

    At any rate, I am looking forward to laying on the driveway of the Red Rock (intentionally) pretty soon and looking at some skids.

  7. #7
    Member Since
    Feb 2007
    Location
    2000 Proton VX - 0776
    Posts
    9,258
    Thanked: 0
    I'll look tonight on mine to see how much clearance between my diff & crossmember. Your new crossmember from Kilby looks very much like the Calmini crossmember on mine. I'm assuming that it's from Calmini because the PO installed their lift kit. I didn't even know mine was aftermarket till I helped someone else with their diff drop installation.

  8. #8
    Member Since
    Jun 2004
    Location
    99 Astral Silver VX #1872 + 99 Ironman WIP
    Posts
    10,613
    Thanked: 1
    Quote Originally Posted by BigSwede View Post
    Getting back to my original point, with the diff drop I am quite sure the crossmember will have to be substantially modified. By eyeball, it looks like the crossmember and diff pinion intersect almost exactly. I am actually thinking it might be best to bridge the crossmember over the driveshaft/diff pinion instead of under it, but a test fitting will be necessary to really judge that.
    How bout cross cutting the Kilby plate where it intersects the cross member, welding mounting tabs to both sides of the cross member, L & R with a nut welded on top, drill holes in the cut Kilby plate that line up with the new mounting tabs, then bolt it up from the bottom...

  9. #9
    Member Since
    Oct 2003
    Location
    1995 Isuzu Trooper LS
    Posts
    1,082
    Thanked: 3
    Not sure if it has enough depth for that...in any case such fine details will have to be sussed out AFTER Moab...

  10. #10
    Member Since
    Feb 2007
    Location
    2000 Proton VX - 0776
    Posts
    9,258
    Thanked: 0
    I'm thinking that the Kilby plate is strong enough to use as the crossmember. Just remove the stock crossmember and modify the crossmember drop brackets for something to bolt the back of the 1st Kilby plate & the front of the 2nd Kilby plate to.

  11. #11
    Member Since
    Oct 2003
    Location
    1995 Isuzu Trooper LS
    Posts
    1,082
    Thanked: 3
    That might be worth looking into...I remember Jerry Lemond telling me that the crossmember there doesn't do much of anything, and he wasn't even sure it is needed!

    But I do hit rocks pretty hard on occasion, so I think something backing that plate joint would be a good idea.

  12. #12
    Member Since
    Oct 2003
    Location
    1995 Isuzu Trooper LS
    Posts
    1,082
    Thanked: 3
    Did the Calmini kit include a diff drop? I wasn't aware of that, but there would be little reason to replace the crossmember otherwise.

  13. #13
    Member Since
    Feb 2007
    Location
    2000 Proton VX - 0776
    Posts
    9,258
    Thanked: 0
    Nope, diff drop NOT included with Calmini lift. I don't know why they provided a new crossmember.

    I just checked & I have less than 0.5 inch clearance between my differential and the crossmember. IIRC we made the diff drops 3 inches & the crossmember drop 1.5 inches.

    Tom
    Last edited by tom4bren : 04/13/2010 at 08:44 AM

  14. #14
    Member Since
    Apr 2010
    Location
    1999, Astral Silver, Vehicross, #1209
    Posts
    1,673
    Thanked: 0
    Not specific about a diff drop though, which is the original question.
    1999 Isuzu Vehicross-#1209- lots of mods - gone
    1995 Honda Passport: Lifted, Locked, 34x10.50's, just a few things..-Click for build thread

  15. #15
    Member Since
    Oct 2010
    Location
    1999 Ebony, 1981
    Posts
    32
    Thanked: 0
    So with VX Kat's Kilby plates up for sale I wanted to see if anyone has thought about this old thread anymore. Will a diff drop fit with the Kilby plates? The answer looks like 'No', but how difficult would it really be to modify the plates? I have the Darlington diff drop sitting in my garage and no kilby plates so I don't have much to compare. Anyone?

Similar Threads

  1. Kilby is in business - Who wants their skid plates?!
    By JHarris1385 in forum VX Modifications...
    Replies: 65
    Last Post: 06/11/2020, 10:54 PM
  2. diff drop
    By ramathorn in forum VX Troubleshooting...
    Replies: 23
    Last Post: 08/23/2012, 12:31 PM
  3. Diff Drop Brackets
    By JHarris1385 in forum VX Modifications...
    Replies: 80
    Last Post: 04/04/2011, 06:40 AM
  4. Any alternatives to Kilby skid plates?
    By DannyDigital in forum VX Modifications...
    Replies: 5
    Last Post: 03/04/2010, 10:44 PM
  5. My diff drop.
    By JHarris1385 in forum VX Modifications...
    Replies: 4
    Last Post: 04/03/2008, 09:30 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
$lv_vb_eventforums_eventdetails