Wheel Adaptors

[Ldub]

Hey, check ebay for Toyota truck 6 bolt spacers. They are like 20 bucks cheaper for the same flippin part. It just needs to b 6x5.5"

Thx Attilla I'll check it right now.
Peace.
Tom

No matter what you decide, make sure the center bore measurement is large enough.

[tomdietrying]

No matter what you decide, make sure the center bore measurement is large enough.

Thanks for the read and the videos Larry. Very interesting. Just to make sure, our center bore is 108 mm right?

Here are the three companies I checked out.
http://www.performancewheel.com/Spac...=6&gacid=#safe
http://cgi.ebay.com/ebaymotors/NISSA...Q5fAccessories
http://cgi.ebay.com/ebaymotors/4-Isu...Q5fAccessories

From what I can tell, the material is the same on all three. (Billet 6061-T6 Aluminumn) The price is the only difference I can tell.
EX. 1 - $220
EX. 2 - $120
EX. 3 - $140

What do you think guys?

Peace.
Tom

[atilla_the_fun]

I really want to get a set of wheel spacers. Are you bringing your stock wheels to the edge of the fender? Thats what I would like to do. I haven't measured and don't know if its 1" or 3/4".

I've got a set of Tom's window brackets that I'm going to sell (mine weren't broken it turns out..) and try and finance a set of these spacers (the nissan/toyota ones).



Hey do we have to cut our studs down for the Isuzu stock 18" wheel to fit?

[Triathlete]

Here are 3 of the better known brands...

[WormGod]

I would avoid wheel spacers. They put more load bearing on your hubs, which means bearings go faster. My advice would be to just find a wheel that has a lesser offset (wider wheel + lower offset = more aggressive wheel well stance). It's a balancing act though. Too much negative offset can still put more load bearing on your hubs.

[kodiak]

I’ve had spacers on mine for the past 3 years without any problems. The ones I have were custom made for a Toyota. They’re ¾ inch. I hand torque the lugs and used loc tite.
[/URL]

[djvx]

Thanks for the read and the videos Larry. Very interesting. Just to make sure, our center bore is 108 mm right?

Here are the three companies I checked out.
http://www.performancewheel.com/Spac...=6&gacid=#safe
http://cgi.ebay.com/ebaymotors/NISSA...Q5fAccessories
http://cgi.ebay.com/ebaymotors/4-Isu...Q5fAccessories

From what I can tell, the material is the same on all three. (Billet 6061-T6 Aluminumn) The price is the only difference I can tell.
EX. 1 - $220
EX. 2 - $120
EX. 3 - $140

What do you think guys?

Peace.
Tom

So Tom, have you decided?

[tomdietrying]

Yeah, I went with the with #2. Material was the same, quality was the same so I got them. They look good.........I put them on this past Saturday. My 285/60/18s Nittos are about 2.5 years old so the thread is a little worn. I know when I buy my new Nittos I'll have to do a little trimming.

We have a mini meet here in Dallas this Sunday, so hopefully I'll get some nice pics.

Peace.
Tom

[atilla_the_fun]

Tom, did you have to grind off the stock studs any?

[tomdietrying]

I was getting some stuff done to my VX, and I had the guys at the shop put them on. It was a real quick process. I forgot to ask them about it.
Peace.
Tom