trooper diff. compatibility

[pbkid]

oh ok, thats not too bad then....around 500-600 in parts??? maybe a few hundred in labor if i had a shop do it??

[Ldub]

oh ok, thats not too bad then....around 500-600 in parts??? maybe a few hundred in labor if i had a shop do it??

Let's wait for the Zeusters response, he has FAR more experience with setting up gears than I do.
On my best day, I might have a rudimentary grasp of the "how to's" of setting up gears...
I have a local homie that'll set em' up for me for fiddy, but I have to do all the R & R, & bring em' to his shop for the setup.
Pulling the sensors has me a little cautious, as even seasond pros (Jerry Lemond) have trouble sometimes, getting them out in reusable condition...

[pbkid]

hmmm...so once again, when i do mine, its best to have a shop do it so i dont have to worry about the sensors because it would be their responsibility to make sure they are removed and replaced properly...

[ZEUS]

Let's wait for the Zeusters response, he has FAR more experience with setting up gears than I do.
On my best day, I might have a rudimentary grasp of the "how to's" of setting up gears...

I don't have that much experience with gear setup, actually. I have participated in a couple of builds on Jeep axles and witnessed the practice, but that's 'bout it. I do think you are correct about setting the preload on the pinion shaft. You shouldn't have to mess with that at all, unless you want to put in a new pinion seal. However, when swapping out the LSD for anything else, you should make sure the gears mesh correctly again. But the guidline is to use the shims that were used for the stock diff in their original locations first, as a starting point. From there, you may or may not have to add, remove, or relocate shims. So it is nice to have shims in hand in case you do need them.

And Jack, I think your estimate is right for the Aussie Locker parts. What I was trying to say is, when having someone set up your diff, whether you wish to install an ARB or an Aussie, they should charge you the same. You will have to drill and tap for the air line though as well. So yeah, to run an ARB, it should cost around $1200 in parts. The Aussie plus carrier/3rd is far less at $5-600 in parts. The install charge of either diff should be about equal though.

Regarding the sensors, that is a personal call. The difference in cost to have a shop work on a removed 3rd versus an installed axle assembly is massive!

[pbkid]

ok, are the sensors something that could just be ordered for the new 3rd?? that way you dont have to worry about taking them out of the old one?

[pbkid]

hmmm...so thats something i need to read in to...because if i can just order new ones then i will not have to worry about keeping those ones in good shape

[pbkid]

ouch...maybe i should just be really careful taking them out huh??

i dunno...maybe this whole locker thing is beyond my ability lol...

maybe an air locker for the front would be easier

[Ascinder]

Hey, I just saw an episode on Extreme 4x4 where they're setting up an ARB in a dana 44. Although we have a third member and they dont, many of the steps are the same, if not similar, and the show would help you guys understand what's going on here. I think you can watch the episodes for free online. Here's a link to this episode:

http://www.powerblocktv.com/site3/in.../ep?ep_show=XT

So, as you can see, you probably will have to mess with the shimming a little there Dub. Also, this is a good read to get ready. Again, it's not identical, but it will set you on the right track concept-wise.

[Ldub]

Hey, I just saw an episode on Extreme 4x4 where they're setting up an ARB in a dana 44. Although we have a third member and they dont, many of the steps are the same, if not similar, and the show would help you guys understand what's going on here. I think you can watch the episodes for free online. Here's a link to this episode:

http://www.powerblocktv.com/site3/in.../ep?ep_show=XT

So, as you can see, you probably will have to mess with the shimming a little there Dub. Also, this is a good read to get ready. Again, it's not identical, but it will set you on the right track concept-wise.

Great info Ascinder...THANKS!...

[Ldub]

The sensors are in the axle housing ends. They need to be removed to get the axle shafts out - at least that was what Spazz told me. So we did remove them successfully. I don't remember exactly why they needed to be pulled though.

The axle shafts won't pull out with the sensors in place...I'VE TRIED...
Then buttoned everything back up, went to Moab, & had fun anyway...