Transmission mount?

[Ldub]

Where can I buy a replacement transmission mount for my 99 vx? Have tried searching and no luck.

Welcome to the Fam...

You could call Merlin @ St. Charles Isuzu...sorry, don't have the 800 number, find it in any post by Tone...

OR, if you're buck$ down & feeling a little creative...you could fix it by drilling a couple holes & "pinning" it solid with a couple grade 8, 1/4" bolts with stainless washers & nylock nuts...







>disclaimer<...I did this about a month ago & so far it's good. But have no idea of the longevity of this fix...

[herbeck]

alright I'll have to call them sooner or later. Thanks.

[etlsport]

so.. what happened to your transmission mounts (both of you?)

[LittleBeast]

Merlin at St Charles 1-800-727-8066 ask for internet discount (10-15% off)

[herbeck]

just totally worn out. just had it on a lift to diagnose a tod problem, unless you absolutely baby the throttle from a stop my vx acts like its slipping in the rear end (no vehicle movement) and shows torque being transferred to the front then slams back into the rear end again. No problems once you are at speed. (20mph and above)

Figured trans fluid, diff fluid, u joints or something. Good levels and fluid. So we started checking for play and spotted the mount. Not sure if its the cause but it needs to be fixed before we can start point fingers somewhere else.

That is of course I've missed something while searching and looking in relevant threads?

thanks littlebeast!

[Ldub]

so.. what happened to your transmission mounts (both of you?)

After reading elsewhere in the forums about another member (Joe Black) who cured his "clunk" noise by replacing the trans. mount, I couldn't NOT take it all apart to see (that wasn't it)...figured as long as I had it out, WTH, might as well pin that sucker solid & never give it another thought...

That lead me to the conclusion that I probably have a broken motor mount, I'll be getting to that "whenever"...maybe even before Moab...

I also have a suspicion that the mounts for the lower links have become egg shaped from violent acceleration & braking...another thing I'm gonna have to look into one of these days.

[Ldub]

After several months of use & abuse, it turns out 1/4" bolts aren't beefy enough. The torque load has sheared off both of the bolts I had in there.

Looks like I've got another project to get done before the snow flies... (gonna upgrade to 3/8 or 1/2")

[nocturnalVX]

I replaced the trans mount and both engine mounts just before Moab. The replacements from Merlin were beefier than the ones that came with the VX, so it must have been an issue that was fixed by Isuzu.

[Ldub]

I replaced the trans mount and both engine mounts just before Moab. The replacements from Merlin were beefier than the ones that came with the VX, so it must have been an issue that was fixed by Isuzu.

All three beefier?

[Ldub]

so.. what happened to your transmission mounts (both of you?)

See post #15...

Oh... did you mean why did they fail in the first place?

IMO, rubber gets old, & being in fairly close proximity to the exhaust speeds the aging process. Mine wasn't shredded, just very spongy.

[tom4bren]

"...proximity to the exhaust speeds the aging process. Mine wasn't shredded, just very spongy."

Are you still talkin 'bout the tranny mount or are you back on the potbelly comment from earlier in the thread?

[Ldub]

"...proximity to the exhaust speeds the aging process. Mine wasn't shredded, just very spongy."

Are you still talkin 'bout the tranny mount or are you back on the potbelly comment from earlier in the thread?

Ahhhhh...top-O-the marnin' to ye Brother Tom...

Starting the week off right I see... (though it's thurs. 4 me)

I'd have to say, at this point, it's anybodys guess...

[tom4bren]

It's what I do

[Moncha]

...You could call Merlin @ St. Charles Isuzu...sorry, don't have the 800 number, find it in any post by Tone...

You will always find it here... Web Links