Buzzing sound in passenger side door?

[Raque Thomas]

Borg Warner is the manufacturer of the TOD system, not an amp. It was mentioned in earlier threads on this site that to rig up a system to turn the TOD on and off it involved cutting the light blue wire coming from the TOD computer under the passenger seat. As was earlier theorized, I think the previous owner of your VX had installed a TOD cut off switch. You can go to Tone's site linked from this site and download the workshop manual, which has electrical diagrams. It may be a whole lot easier to just take the relay to an electronics place to match it up, and then hook it back up as it was using a new (and non-buzzing) relay. Good luck, and let us know how it turns out!

[AREA 51]

It looks like the relay is shunting the tod wire. To where, I can't tell, from the picture.

It may be that this relay is wired to circumvent the tod warning light.

Did your tod system ever function properly?

I see other wires in your picture. A yellow and another with a solderless connector. Where do those wires go?

I'd suggest removing the silver splice connector on the blue- blue- white wires and then make a good splice of the blue- blue wires, eliminating the white wire that appears to be tapped off of and NOT interrupting the blue tod wire. You should then be able to remove the relay with no adverse effects on the tod system.

[mdwyer]

By the way, I might know why your stereo won't work: The ground wire in the radio harness isn't connected to anything. The (-) power lead to the stereo goes through the frame -- not the harness.

I yanked my stock radio, plugged in the new one and it didn't work! So I plugged the stock radio back in, and IT didn't work anymore! At this point, I just gave up and decided to stuff everything back into the dash and get help.

As soon as the stock radio grounded itself to frame, it kicked on!

Once I ran a pigtail from some grounded metal to the radio, the new stereo worked great! Hopefully, your problem is just as simple.

[logan5]

Thanks a lot for all the info guys. I returned my stereo and will be purchasing another soon. When I do I'll follow your advice mdwyer...

Area 51, I'll check where those wires go and post. I'm a little nervous about the TOD now. Is it any indication that it's working if when I put it into low all the lights come on for the TOD and I get more power (ie: going up a hill)? I've put my VX in low when I couldn't climb a hill in high and the low worked as just described. How do I know if the high is working? I drove in a lot of rain and I don't remember the TOD lights all coming on, only the lower rung of lights remained lit. I know the power gets distributed as needed and I'm wondering when the 2nd or 3rd rung of TOD lights are supposed to come on...Is there any way of testing this? Reason I need to know is that if somehow the TOD is screwy then nothing I do will fix the problem. Again, when I remove the relay the light comes on so finding out if my TOD is OK I think would be a good place to start. Thanks a lot guys!

Raque Thomas: I will definitely download the manuals you suggested. Also, I tried replacing the relay and it makes the same noise so it must not be broken.

[etlsport]

if the same buzzing noise happened it means that the wiring was done wrong and the relay was shorting.. probably just mixed up what location two of the wires should have plugged into on the relay

as for your TOD.. DO NOT DO NOT put it in 4Lo unless you are somewhere that your wheels can freely slip (loose dirt, gravel, snow) or you will bind up your driveline.. during everyday driving and even in rain its normal to have 1 bar on the front wheels lit up all the time (except at start and up to 5-10mph, then its usually 0 in the front) to test your tod find a dirt or gravel road and from a dead stop hit the gas as hard as you can and your tod should light up all 3 front wheel bars at least momentarily... if its safe to do so you may want to slam on your brakes after that to let your tod kick in as mentioned in another thread

if i were you, like area51 said... i would remove the relay and reattach the blue wires together, thats what is causing your tod to flash when you disconnect the relay, the blue wire being discontinued... i couldnt tell from the photo whether or not there are any other wires spliced from the harness going into the TOD, but if there are i would recommend reattaching it to the rest of the wires, after that tape off any remaining loose wires (probably your ground and a hot wire, so be weary of that)

[AREA 51]

After thinking about this for a while, I'm wondering if the previous owner might've used the coil in the relay in place of the resistor described in the tod disconnect theory. That would explain the constant buzzing when there is power on the blue wire (almost always), but wouldn't explain the warning light when relay removed since that would break the connection from tod wire- relay coil- ground (unless something is wrong with the tod).

[logan5]

The blue wire is not disconnected from the TOD brain. There is no severe in the blue wire at all. They cut the plastic guarding the wire and wrapped the wire from the relay around it and taped it up. Thats why I figured if I removed the relay nothing would happen because the blue wire is still intact.

I am looking at the manuals for the TOD now and I'll tell you what I find. Thanks again!!