rebuild

[ZEUS]

moonraker. im very interested. i just blew up the motor in my vx so....

Wait wait wait... pbkid, first you slid into a Tahoe or something and now you blew up your motor? What's going on in Larkspur?

MoonRaker, I would like to see some detailed pics of all that stuff you plan to do. It should be interesting!

[MoonRaker]

I havent heard back from any moderators. Im not a sight supporter and im not going to pay to post pics that are for my use. Like I said to them in an Email, im willing to share pics and give explinations of what im doing and why. Thats going to take me a long time to just write. Its probly going to be about 100 to 150 pics. Every detail. You might want to send them somthing in referance to this if your interested. All they have to do is push a button. I bet its going to draw more members also, only benifits.

[Anita]

Moonraker,

I would wait a little longer than an afternoon for Scott (the site owner) to get back to you. I assume you sent the email to him, since it didnt come to my moderator's box.

Scott works a varied schedule so give him some time. I will alert him as well about your offer.

[CrnCnn]

I wrote Scott a PM and he took a few days to get back at me, not complaining, just letting you know. Some people dont have a whole lot of time. Me on the other hand have no life. So I am on here alot.

[MoonRaker]

Cool CRNCNN, after I finish and break in my engine im headed that way. Tryed for a glamis newyear but had to call it off because of this problem. this is a big thanks to Isuzu for not replacing my motor when I told them that it was on its way out. That was after I purchased it and tryed my best to take good care of it and make it last. Almost 5,000 miles after warrenty experation. Isuzu you built an impressive machine but you need to take better care of your customers. Enough of that. Lets get down to buissnes.

[MoonRaker]

First and for most, get everthing thats in the way out of the way, keep the area clean around and under the vehical. The hood, remove it, if its out of the way it keeps your head from bleeding, trust me. Next is the battery and complete air box. There is a 12mm nut/bolt combination to the left of it wich also holds an A/C line. Theres 2 12mm bolts inside the airbox also holding the airbox down. Unplug the MAF sensor theres 2 hoses also, remove them from the engine side to cut the clutter, one leads to the PCV just pop the PCV out and leave it conected to the hose and the other goes to the left side of the motor. Theres a phillips screw hose clamp holding the pipe to the throttle body. Remove the entire assembly as one piece so it speeds reassemly. Ok, ive gotten a little bit more then that done but the rest requires pics so it easyer to understand. Keep everthing organized like tools and just about everthing because theres alot more parts on the way. Bag all of the small parts with lables. Some of the bolts can be replaced without being in the way, use your own judjment on wich ones to do this with. This also helps you during assembly because it keeps you from having to figure out were it goes.

[Moncha]

Thanks Anita, I got your PM.

Yes, I am very sorry that I'm not a fixture on the site right now. I'm right in the middle of combining 2 detective positions and a 3 million $$ upgrade to our communications center.

No one needs to, or is obliged to donate to the site. It is mearly out on the kindness of hearts to help offset the high cost of running a place like this.
All contributions, dollars, photos, articles, etc.. are always accepted with great appreciation. You do not need to be a site supporter to have an article published.

An article the size of what you are proposing is quite an undertaking and will take some planning to get it to display correctly. Send me, by email, what you have if possible and I'll get it to where it needs to go.

Thank you again in advance for your contribution.

Scott