-
Here is my response to some questions about VX KAT's pix of Tim installing her brackets:
1. What is he using in Pic 9 to remove the old bracket? It looks like a small sawzall.
That's funny. I never really looked at the pictures till you asked (they are of Tim installing the brackets on VX KAT's). I thought I was being creative when I used a rotary tool to make that very same cut using a drywall bit. It looks like he's using a dremmel. You may be able to skip this step if you want. Just slide a razor blade under the tab & cut through the glue on both sides of the glass. Of course if that doesn't work, you'll have to make the cut (but several of the tabs actually fell off when we removed the window from the door). If you have to make the cut, it helps to break the tab to give yourself more room to work.
2. On Pic 10 is the SBC bracket mounted 1st using both bolts to the regulator?
That's how I did it. Leave the bolts 'wobbly' loose at this point though. Once the adhesive is applied and the glass dropped into the slot, roll the window up to make sure everything is aligned. Only tighten the bolts with the window in the up position.
3. It looks like on Pics 11 & 13 the glue is applied first then window is dropped into the glue using the guides on the glass to the bracket?
Yes it is. You'll want a good bonding surface so apply the adhesive liberally and let it squish out. Remember, adhesive that you can scrape off after the install isn't providing any bonding strength so you can leave it in place or clean it off (your preference). On all 4 of the windows that we did, I bolted in the brackets first and then added the adhesive (I don't know why). In retrospect I should have put the adhesive in the bracket first since the center post on the regulator is kind of in the way and makes it difficult.
4. On pic 15 the bracket bolt is off and don?t know why?
Yer right. The bolt isn't there but it looks like it is in the next picture. I don't know why he removed it for that step - it doesn't need to be.
5. What is pic 17 trying to show?
I'm not sure. If I had to guess, I'd say that he's showing that the weather strip is not properly bonded to the front channel. Or maybe he's showing the marks from where she had previously widened her channel.
From what I've seen, fixing the window is a combination of things. The SBC brackets are the largest contributor though. Mine still tilts so I've got to open it back up & try some of the other fixes. I need to add a couple of washers between the SBC bracket and the mounting arm (CSTYLES did that after the install & fixed the last of his problems), this forces the regulator against the center guide and relieves stress from the guide tabs which are also breaking. Widen the front channel to take out the remaining binding. There's supposed to be an adjustment that will allow you to push the front channel forward slightly to keep it from binding on the edge of the glass.
-
I finally got my passenger window working (acceptable but not perfect). It still tilts but not enough to come out of the rear weather stripping. I tried widening the front channel - No Go. I tried adjusting the front channel both forward and back - No Go. What worked for me was to add some washers in key locations to force the window guide against the regulator (not sure if I'm using the right terms) - basically the part that slides up & down the center post.
Each of the 6 bolts got 2 washers except the top 2. I could only fit 1 washer between the door panel and the center post there.
-
tom posted his own picture!! :dance:
-
Tom, I had the same results when I did mine..the window still tipped down in front when going up. I used a Dremel and elongated the front hole about 1/4 inch in the SBC bracket making the hole lower. When tightening the bolts I just force the wndow up in the front bringing the bolt down into the elogation then tightening both bolts. That causes all the slack in the guides to be taken up and puts more lift in the front. That combined with widening the track a bit, forcing the front guide forward a bit and silicone slickem my windows work great. I know you will find the "sweet spot" eventually.
-
Travelin2,
Thanks dude. I'm not going to open it back up for any more adjustments right now. If it starts jumping tho, I'll give your trick a try.
Eric,
Don't make me come up there & learn you some manners.:slap:
BTW, my hands aren't as shakey as the arrows in the pic would lead you to believe. I was using a trackball instead of a mouse.:work:
