Printable View
I remvoved my rear seat about a month ago. I lined the floor with a big sheet of the tool drawer liner made from a rubber material. Keeps items from sliding, plus you could save a bit on gas from hauling around that extra 60 to 70 pounds! I also just put the bolts back in for now and since the carpet has velcro flaps it looks good enough.
It's seems everyone has made this way too complicated. I simply removed the two hinge pins and replaced them with $5 pull pins I found at Ace. I retained the plastic inserts that supported the original hinge pins and that has kept everything from squeaking. I can install my seat in less than a minute and it's even quicker to take out. I have considered using the seat mounts for a full size spare tire mount (baja style) that's just as quick to remove. Options... it's a beautiful thing.
Zeus,
You know, you can't just post something like this and not post pictures at the same time! :)
Seriously, I would like to see some pictures of your rig with the Ace pins in place...if you have the time.
Thanks - Bart
Quote:
Originally Posted by ZEUS
Well as luck would have it... as I was posting I went looking for the pins I took out before the 'ZuZoo so I could post pics but they are so "convenient" that they seem to have disappeared! I'm thinking the landlord took them thinking they were his. Anyway, I'll make my way to Ace tomorrow to price, photo and pick some more up.
http://img157.imageshack.us/img157/3...kets0013vl.jpg
http://img157.imageshack.us/img157/6...kets0024lo.jpg
http://img157.imageshack.us/img157/3...kets0036az.jpg
Ace Hardware - (2) 5/16" x 2-3/4" zinc plated pins = $4.80 plus tax = quick release rear seat. I hope the pics posted alright. It's hard to see but the plastic sleeves are on the seat mounts holding the pins.
NICE!
Cool idea!
Thanks for posting the pics.
Bart
Nice! A simple solution to a simple problem. I like that. I may just have to pick me up a set of those. ;Db;
So I'm starting to start on this as we type, as this is the first temp. mod for my Tahoe trip this weekend...
do you just hammer out the hinge pins or is there something to unscrew first?
There is a little retainer washer on the pins - I first used a thin screwdriver to get underneath it and started prying at it. I then used a hammer to move it out so the retainer is up against the bracket again then pryed some more until the retainer slipped off. I think you could use a c-clamp and socket as a press though. Put the socket on the side that does not have the removable retainer and tighten. The hinge pin should slide into the socket until the retainer slides off the other end.
Thanks Zeus,
But Darn It!
Now I have something else I have to do on my VX. :)
At least it won't take long...
I like this mod.
Can you pin them into the roof rack, so the kids can ride up there?
I always tell them that I'm going to duct tape them on top. They like the Idea.
Too bad it's not the fifties anymore, you could get away with it then.
I'll do this mod anyway, just for the option.
Who knows, maybe my next wife will haul the kids. :) :) :)
Thanks guys,
got them out this morning.
I tried to bang them out yesterday but that retainer washer looked like a bit more trouble than it actually is.
I just pryed under it with a thin scregie and then it all popped apart in minutes.
On to Tahoe!
Cy
Yep, a while back I did basically the same thing Zeus has done. I used a pair of small hitch pins that came with several holes in them, and put a retainer clip through each to secure them. The fit is nice and tight, so there are no noises from it. I also kept all the old original parts if I ever want them. It was really cheap (like under $3). Very simple.
I actually like what Zeus did a bit better, because the whole thing is just one piece, rather than separate pin and pin clip. I actually have one of those like Zeus posted on my boat trailer's latch at work but had never thought to use one of those this way because I'd already done the mod before I had the current job. I may just switch to that. I know the ones I've seen around are of a smaller diameter than the holes in the brackets, so unless you can find them in different sizes, yeah, probably need to retain those little plastic pieces like he did.
Hey etlsport !
I got all my gear to install the aftermarket sound system in my toy,since you did the same job i was wondering if you can e-mail to me the pics of the rear panels removed so i can follow up the procedures.
I don't know if you install any amp,but if you do please explain me where & how do you run the power cable through the firewall;I was took an close eye at the firewall to find out an path,but to me there's no clear spot to drill in.
My e-mail is VZEEI6VS@MSN.COM OR GUSSIE2000@HOTMAIL.COM.
I'll appretiate all you competence.
Hey,soon i'll making a trip to PA to visit my aunt so if the a opportunity we may meet up.
take care buddy.See ya ! :)