Clear Coat

Dear VXers,
My VX is coming up to its 3rd birthday in a few days so I wanted to do something extra special. I've noticed that it does not shine as much as before even after polishing. I wanted a new paint job but, can't afford it right now, so I was wondering, can I just have the paint shop apply a few coats of clear coat over the existing original paint? I believe from all the hundreds of washes and Acid rain may have worn away at the clear coat and thats why its not shinny as before, is this possible?

Regards,
Concerned Parent:confused:

From what I've seen, our clear coat from the factory is pretty thin. If you've been using an orbital polisher then maybe you've worn through the clear in a few places, like on the high spots at the edges along fenders or the ribs on the doors. If you've just been hand polishing and waxing then I imagine the clear coat is fine and all the old wax is dulling the finish. Maybe try an orbital polisher and a compound with a mild cut. Also, you might check with an auto paint shop and get a nice professional polishing pad rather than those fuzzy wuzzy whilrly ones that come from WalMart. A good polishing pad runs around twenty to twenty five bucks if I remember right, but its worth it. They can also recommend an appropriate polish for the clear coat. I use the 3M products. Triathlete and I are going to be doing this same project in a week or so, and I can post what we use and how it goes if its any help.

Of course we'll have to experiment on Triathlete's truck first... ;eekg; ;eeko; ;eekp;

You can actually get some places to do a special 3 to 5 layer clear coat for pretty cheap. You might check pepboys, last time I was in the one here, they'll do a triple clear coat for a few hundred dollars. Its supposed to clear up all the little scratches, swirls etc. I'm considering getting it done, but I wanted to wait till after the badlands run in april.

Thanks Guys:
VXcaver/Triathlete, can't wait to see the results!
omegavx-I'll look into it!
:thumbup:

3m Products? Moncha did that on his ride right? I just got mine painted and want to put the protectants in the front to prolong the life of the color shine and get away from those damn bug and rock nik's...

ANy advice as to how long I should wait before applying, I know i've got one more polishing before I even consider 3M

Bantan:
I would not recommend new clear coat ...... new paint ..... etc ..... unless it is *absolutely* required. I would attempt to keep the factory finish as long as possible.
.
Plus, I believe it will cost much more than a few hundred dollars to have the job done correctly.
.
I (also) would not use a a heavy - or even mid abrasive compound ...... not on a base coat/clear coat finish. Instead, look into a hand glaze ........ 3M makes some good products that many use. Hand glaze should remove the fine scratches and restore the shine - given there is no underlying problem.
.
If applying the glaze by hand does not do the job, buffing (the glaze) with a foam pad - *not* a wool pad - would be the next step. Buffing should be done by somebody that has alot of experience.
.
t2p

Bantan, I have to agree with T2P, there are a multitude of products out there from 3M and other manufacturers like Meguires to bring your paint back to life. I am the national marketing manager for 3M products for my company. I have 26 years experience selling and using many of their products, including their hand glaze. I would do as T2P has recommended and try the 3M Imperial Hand Glaze. This product has no abrasives in it and it will fill small swirl marks and scratches and greatly improve the appearance of your paint. This product can be used on new paint as well as your older finish with no risk of damaging the finish. Hand glazes are designed to polish, fill and seal the paint. They are not waxes and do not offer the protection that a good wax job does. Use caution not to apply on a relatively warm or hot surface. It best applied in the shade or in an enclosed area, like your garage out of the sun. Only do about a 2' X 2' area at one time, apply, let dry, buff then move to the next area. If you do this, I think you will see a significant improvement in your paints appearance, if in fact the clear coat is intact and you have something to work with.

3m extra cut an' 3m machine glaze after the 2000 wet sand.Yeah, we use only 3m in the shop and always toss a coat of Meguire's #26 yellow wax on any paint work we do.

Thanks Guys, I will have to wait a bit for the weather to warm up some to try out these products.

Get the 3M hand glaze, BUT not the product sold in the stores or pro shops. Get the 3M hand glaze that is used by the auto repair shops. It works much better and its a snap to use. To get it you will need to go to one one the suppliers that the auto shops use. There is one in Flushing Queens That I got mine , but I forget the name of the place. I will try and get you the nameo of the place. This is the stuff that comes in 2 sizes. Small size about $16, large about $35. This is not the stuff sold in retail shops, its a different chemical & it doesnt come in a grey bottle like that of the stores, this ones more like a tan color in a cylinder shaped plastic bottle & will also carry the same name 3M HAND GLAZE. You will love the stuff. Good Luck, Bruce

Quote:

---

Originally posted by Sheik-YurBooty
Get the 3M hand glaze, BUT not the product sold in the stores or pro shops. Get the 3M hand glaze that is used by the auto repair shops. It works much better and its a snap to use. To get it you will need to go to one one the suppliers that the auto shops use. There is one in Flushing Queens That I got mine , but I forget the name of the place. I will try and get you the nameo of the place. This is the stuff that comes in 2 sizes. Small size about $16, large about $35. This is not the stuff sold in retail shops, its a different chemical & it doesnt come in a grey bottle like that of the stores, this ones more like a tan color in a cylinder shaped plastic bottle & will also carry the same name 3M HAND GLAZE. You will love the stuff. Good Luck, Bruce

---

Yo man, where you been?
Thanks for the info. Hook a brother up, when you get the name of the place.
Peace
Mercer/Bantan

So Triathlete and I experimented on his clear coat Sunday... ;eekr; The task was removing all the nasty "desert racing stripes" that have scuffed the finish. We used my old buffer/polisher from my airbrushing days and shined up his clear using 3M liquid microfinishing compound on a Mequires soft buff foam buffing pad. He used some Zymol wax on it afterwards and the finish looks like brand new. ;Db;

http://www.vehicross.info/gallery/da...tripes-med.jpg

Now, thats how I want mine to look.
VXcaver, got a pic of the entire VX after Buffing?

And here is the same area after the Zymol (1st coat). It reflects nicely!;Dy; ;Dy; ;Dy; ;Dy;
http://pstr-g02.ygpweb.aol.com/data3...coVlHP0300.jpg

Bantan,
I'll be going out and putting the 2nd coat on shortly. I will take a pic of the whole enchilada then!:thumbup: