Recovery /snatch straps 101...to use Billy's words....

[VX KAT]

Got 2 Crosby 3/4" shackles today, it fits on the rear eyelet, me likey!
but can't fit it on the front two holes (well, actually I only tried the front driver side). Not enough space width-wise down there to get pin open far enough to slip it through hole, it's at a slight angle. Tried it both ways too.

I might be able to get the next size down 5/8" on which is only 3.25 ton......so Billy how the heck did you get a 3/4" in let alone a 1" on there....the BFH method? I'm not sure I want to beat on the metal thing there...

[Marlin]

Got 2 Crosby 3/4" shackles today, it fits on the rear eyelet, me likey!
but can't fit it on the front two holes (well, actually I only tried the front driver side). Not enough space width-wise down there to get pin open far enough to slip it through hole, it's at a slight angle. Tried it both ways too.

I might be able to get the next size down 5/8" on which is only 3.25 ton......so Billy how the heck did you get a 3/4" in let alone a 1" on there....the BFH method? I'm not sure I want to beat on the metal thing there...
[

Those are actually not recovery points, I use mine as such, but the last time I used the front one, it actually bent that tab all up. Had to bang it back into place with a sledge. That means it is even weaker now. But they do look awesome!!!
Recovery points should be attached to the frame, such as our front tow hook. A hitch insert would work as well since it bolts directly to the frame. I think maybe those holes were for shipping tie downs?

[VX KAT]

My front end has been rearranged by a rock or two apparently...they just fit!

Oh, I see, the "BFR" method.....

Those are actually not recovery points, I use mine as such, but the last time I used the front one, it actually bent that tab all up. Had to bang it back into place with a sledge. That means it is even weaker now. But they do look awesome!!!
Recovery points should be attached to the frame, such as our front tow hook. A hitch insert would work as well since it bolts directly to the frame. I think maybe those holes were for shipping tie downs?

Yeah, that was pointed out earlier in the thread, if I called them recovery points that's just me calling me that, and I've decided to just go with them for now, no front receiver etc....

[Sprey]

I agree with marlin thats why i have had this built.
Bolts into factory towhook bolts and has 2 rated hooks on each side.
Best part about it bolt on bolt off . It is flat with the end front bumper so people with the extra skidplates might not be possible.

[Marlin]

I agree with marlin thats why i have had this built.
Bolts into factory towhook bolts and has 2 rated hooks on each side.
Best part about it bolt on bolt off . It is flat with the end front bumper so people with the extra skidplates might not be possible.

Looks pretty mean...nice. The only problem I see is that it might get hung up on rocks, or get bashed up pretty good. Looks pretty cool though.

[Sprey]

Looks pretty mean...nice. The only problem I see is that it might get hung up on rocks, or get bashed up pretty good. Looks pretty cool though.

Yea your right, last time when i went out, it was good for picking up mud Lol.
But also does give a bit of protection so thats sorta a bonus.

[VX KAT]

Found this thread on the web.....way to keep the shackles from rattling (and in this guy's case, not scratch his bumper). Good pics on page 1 & 2. Never heard of "Glad Hand" seals before, (somethin' about them going on big rig trucker's air lines) but got rubber grommets at the hardware store that do the same thing.

No real problem putting them on the back, but a bear getting them on the front with so little work space....I may just skip the front, they aren't scratching anything and probably can't hear them rattle down there anyway. May do something like it on Dave's front shackles as the FJ OEM skid plate is in the way & they're banging into it. Now he wants custom skids like mine.....
http://www.thenewx.org/forum/showthread.php?t=1423

First 2 pics show glad hand seal being used, 3rd pic shows ballcock shank washer.